diff options
Diffstat (limited to 'config.txt')
| -rw-r--r-- | config.txt | 140 |
1 files changed, 140 insertions, 0 deletions
diff --git a/config.txt b/config.txt new file mode 100644 index 000000000000..47b982b7c70a --- /dev/null +++ b/config.txt @@ -0,0 +1,140 @@ +# Uncomment some or all of these to enable the optional hardware interfaces +# Params: +# i2c_arm Set to "on" to enable the ARM's i2c interface +# (default "off") +# i2c_vc Set to "on" to enable the i2c interface +# usually reserved for the VideoCore processor +# (default "off") +# i2c_arm_baudrate Set the baudrate of the ARM's i2c interface +# (default "100000") +# i2c_vc_baudrate Set the baudrate of the VideoCore i2c interface +# (default "100000") +# i2c_baudrate An alias for i2c_arm_baudrate +# i2s Set to "on" to enable the i2s interface +# (default "off") +# spi Set to "on" to enable the spi interfaces +# (default "off") +# act_led_trigger Choose which activity the LED tracks. +# Use "heartbeat" for a nice load indicator. +# (default "mmc") +# act_led_activelow Set to "on" to invert the sense of the LED +# (default "off") +# act_led_gpio Set which GPIO to use for the activity LED +# (in case you want to connect it to an external +# device) +# (default "16" on a non-Plus board, "47" on a +# Plus or Pi 2) +# pwr_led_trigger +# pwr_led_activelow +# pwr_led_gpio +# As for act_led_*, but using the PWR LED. +# Not available on Model A/B boards. +# N.B. It is recommended to only enable those interfaces that are needed. +# Leaving all interfaces enabled can lead to unwanted behaviour (i2c_vc +# interfering with Pi Camera, I2S and SPI hogging GPIO pins, etc.) +# Note also that i2c, i2c_arm and i2c_vc are aliases for the physical +# interfaces i2c0 and i2c1. Use of the numeric variants is still possible +# but deprecated because the ARM/VC assignments differ between board +# revisions. The same board-specific mapping applies to i2c_baudrate, +# and the other i2c baudrate parameters. + +#device_tree_param=i2c_arm=on +#device_tree_param=i2c_vc=on +#device_tree_param=i2s=on +#device_tree_param=spi=on +#device_tree_param=act_led_trigger=mmc + +# +# See /boot/overlays/README for a detailed list and description of additional +# overlays and their configuration options. +# + +# Uncomment if you get no picture on HDMI for a default "safe" mode +#hdmi_safe=1 + +# Uncomment this if your display has a black border of unused pixels visible +# and your display can output without overscan +#disable_overscan=1 + +# Uncomment the following to adjust overscan. Use positive numbers if console +# goes off screen, and negative if there is too much border +#overscan_left=16 +#overscan_right=16 +#overscan_top=16 +#overscan_bottom=16 + +# Uncomment to force a console size. By default it will be display's size minus +# overscan. +#framebuffer_width=1280 +#framebuffer_height=720 + +# Uncomment if hdmi display is not detected and composite is being output +#hdmi_force_hotplug=1 + +# Uncomment to force a specific HDMI mode (this will force VGA) +#hdmi_group=1 +#hdmi_mode=1 + +# Uncomment to force a HDMI mode rather than DVI. This can make audio work in +# DMT (computer monitor) modes +#hdmi_drive=2 + +# Uncomment to set monitor mode to DMT +#hdmi_group=2 + +# Uncomment to increase signal to HDMI, if you have interference, blanking, or +# no display +#config_hdmi_boost=4 + +# Uncomment for composite PAL +#sdtv_mode=2 + +# Uncomment to overclock the ARM core. 700 MHz is the default. +#arm_freq=800 + +# for more options see http://elinux.org/RPi_config.txt + +## Some over clocking settings, governor already set to ondemand + +##None +#arm_freq=700 +#core_freq=250 +#sdram_freq=400 +#over_voltage=0 + +##Modest +#arm_freq=800 +#core_freq=300 +#sdram_freq=400 +#over_voltage=0 + +##Medium +#arm_freq=900 +#core_freq=333 +#sdram_freq=450 +#over_voltage=2 + +##High +#arm_freq=950 +#core_freq=450 +#sdram_freq=450 +#over_voltage=6 + +##Turbo +#arm_freq=1000 +#core_freq=500 +#sdram_freq=500 +#over_voltage=6 + +#gpu_mem=64 +lcd_rotate=2 + +mask_gpu_interrupt0=0x400 # VPU shouldn't handle V3D interrupts +avoid_warnings=2 # VPU shouldn't smash our display setup. + +#dtoverlay=vc4-kms-v3d +#dtoverlay=rpi-ft5406 + +avoid_warnings=2 +#disable_overscan=1 +#dtoverlay=rpi-backlight |