// SPDX-License-Identifier: GPL-2.0-only /* * Driver for Goodix Touchscreens * * Copyright (c) 2014 Red Hat Inc. * Copyright (c) 2015 K. Merker * * This code is based on gt9xx.c authored by andrew@goodix.com: * * 2010 - 2012 Goodix Technology. */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include struct goodix_ts_data; struct goodix_chip_data { u16 config_addr; int config_len; int (*check_config)(struct goodix_ts_data *, const struct firmware *); }; struct goodix_ts_data { struct i2c_client *client; struct input_dev *input_dev; const struct goodix_chip_data *chip; struct touchscreen_properties prop; unsigned int max_touch_num; unsigned int int_trigger_type; struct regulator *avdd28; struct regulator *vddio; struct gpio_desc *gpiod_int; struct gpio_desc *gpiod_rst; u16 id; u16 version; const char *cfg_name; struct completion firmware_loading_complete; unsigned long irq_flags; }; #define GOODIX_GPIO_INT_NAME "irq" #define GOODIX_GPIO_RST_NAME "reset" #define GOODIX_MAX_HEIGHT 4096 #define GOODIX_MAX_WIDTH 4096 #define GOODIX_INT_TRIGGER 1 #define GOODIX_CONTACT_SIZE 8 #define GOODIX_MAX_CONTACTS 10 #define GOODIX_CONFIG_MAX_LENGTH 240 #define GOODIX_CONFIG_911_LENGTH 186 #define GOODIX_CONFIG_967_LENGTH 228 /* Register defines */ #define GOODIX_REG_COMMAND 0x8040 #define GOODIX_CMD_SCREEN_OFF 0x05 #define GOODIX_READ_COOR_ADDR 0x814E #define GOODIX_GT1X_REG_CONFIG_DATA 0x8050 #define GOODIX_GT9X_REG_CONFIG_DATA 0x8047 #define GOODIX_REG_ID 0x8140 #define GOODIX_BUFFER_STATUS_READY BIT(7) #define GOODIX_BUFFER_STATUS_TIMEOUT 20 #define RESOLUTION_LOC 1 #define MAX_CONTACTS_LOC 5 #define TRIGGER_LOC 6 static int goodix_check_cfg_8(struct goodix_ts_data *ts, const struct firmware *cfg); static int goodix_check_cfg_16(struct goodix_ts_data *ts, const struct firmware *cfg); static const struct goodix_chip_data gt1x_chip_data = { .config_addr = GOODIX_GT1X_REG_CONFIG_DATA, .config_len = GOODIX_CONFIG_MAX_LENGTH, .check_config = goodix_check_cfg_16, }; static const struct goodix_chip_data gt911_chip_data = { .config_addr = GOODIX_GT9X_REG_CONFIG_DATA, .config_len = GOODIX_CONFIG_911_LENGTH, .check_config = goodix_check_cfg_8, }; static const struct goodix_chip_data gt967_chip_data = { .config_addr = GOODIX_GT9X_REG_CONFIG_DATA, .config_len = GOODIX_CONFIG_967_LENGTH, .check_config = goodix_check_cfg_8, }; static const struct goodix_chip_data gt9x_chip_data = { .config_addr = GOODIX_GT9X_REG_CONFIG_DATA, .config_len = GOODIX_CONFIG_MAX_LENGTH, .check_config = goodix_check_cfg_8, }; static const unsigned long goodix_irq_flags[] = { IRQ_TYPE_EDGE_RISING, IRQ_TYPE_EDGE_FALLING, IRQ_TYPE_LEVEL_LOW, IRQ_TYPE_LEVEL_HIGH, }; /* * Those tablets have their coordinates origin at the bottom right * of the tablet, as if rotated 180 degrees */ static const struct dmi_system_id rotated_screen[] = { #if defined(CONFIG_DMI) && defined(CONFIG_X86) { .ident = "WinBook TW100", .matches = { DMI_MATCH(DMI_SYS_VENDOR, "WinBook"), DMI_MATCH(DMI_PRODUCT_NAME, "TW100") } }, { .ident = "WinBook TW700", .matches = { DMI_MATCH(DMI_SYS_VENDOR, "WinBook"), DMI_MATCH(DMI_PRODUCT_NAME, "TW700") }, }, #endif {} }; #ifdef CONFIG_ACPI static const struct acpi_gpio_params irq_gpios_active_high = { 0, 0, false }; static const struct acpi_gpio_params reset_gpios_active_high = { 1, 0, false }; static const struct acpi_gpio_mapping gpio_mapping_order_normal_irq_active_high[] = { { "irq-gpios", &irq_gpios_active_high, 1 }, { "reset-gpios", &reset_gpios_active_high, 1 }, {} }; /* * Devices that need acpi_gpio_mapping to function correctly */ static const struct dmi_system_id need_gpio_mapping[] = { #if defined(CONFIG_DMI) && defined(CONFIG_X86) { .ident = "GPD P2 Max", .matches = { DMI_MATCH(DMI_SYS_VENDOR, "GPD"), DMI_MATCH(DMI_PRODUCT_NAME, "P2 MAX") }, .driver_data = &gpio_mapping_order_normal_irq_active_high }, #endif {} }; #endif /** * goodix_i2c_read - read data from a register of the i2c slave device. * * @client: i2c device. * @reg: the register to read from. * @buf: raw write data buffer. * @len: length of the buffer to write */ static int goodix_i2c_read(struct i2c_client *client, u16 reg, u8 *buf, int len) { struct i2c_msg msgs[2]; __be16 wbuf = cpu_to_be16(reg); int ret; msgs[0].flags = 0; msgs[0].addr = client->addr; msgs[0].len = 2; msgs[0].buf = (u8 *)&wbuf; msgs[1].flags = I2C_M_RD; msgs[1].addr = client->addr; msgs[1].len = len; msgs[1].buf = buf; ret = i2c_transfer(client->adapter, msgs, 2); return ret < 0 ? ret : (ret != ARRAY_SIZE(msgs) ? -EIO : 0); } /** * goodix_i2c_write - write data to a register of the i2c slave device. * * @client: i2c device. * @reg: the register to write to. * @buf: raw data buffer to write. * @len: length of the buffer to write */ static int goodix_i2c_write(struct i2c_client *client, u16 reg, const u8 *buf, unsigned len) { u8 *addr_buf; struct i2c_msg msg; int ret; addr_buf = kmalloc(len + 2, GFP_KERNEL); if (!addr_buf) return -ENOMEM; addr_buf[0] = reg >> 8; addr_buf[1] = reg & 0xFF; memcpy(&addr_buf[2], buf, len); msg.flags = 0; msg.addr = client->addr; msg.buf = addr_buf; msg.len = len + 2; ret = i2c_transfer(client->adapter, &msg, 1); kfree(addr_buf); return ret < 0 ? ret : (ret != 1 ? -EIO : 0); } static int goodix_i2c_write_u8(struct i2c_client *client, u16 reg, u8 value) { return goodix_i2c_write(client, reg, &value, sizeof(value)); } static const struct goodix_chip_data *goodix_get_chip_data(u16 id) { switch (id) { case 1151: case 5663: case 5688: return >1x_chip_data; case 911: case 9271: case 9110: case 927: case 928: return >911_chip_data; case 912: case 967: return >967_chip_data; default: return >9x_chip_data; } } static int goodix_ts_read_input_report(struct goodix_ts_data *ts, u8 *data) { unsigned long max_timeout; int touch_num; int error; /* * The 'buffer status' bit, which indicates that the data is valid, is * not set as soon as the interrupt is raised, but slightly after. * This takes around 10 ms to happen, so we poll for 20 ms. */ max_timeout = jiffies + msecs_to_jiffies(GOODIX_BUFFER_STATUS_TIMEOUT); do { error = goodix_i2c_read(ts->client, GOODIX_READ_COOR_ADDR, data, GOODIX_CONTACT_SIZE + 1); if (error) { dev_err(&ts->client->dev, "I2C transfer error: %d\n", error); return error; } if (data[0] & GOODIX_BUFFER_STATUS_READY) { touch_num = data[0] & 0x0f; if (touch_num > ts->max_touch_num) return -EPROTO; if (touch_num > 1) { data += 1 + GOODIX_CONTACT_SIZE; error = goodix_i2c_read(ts->client, GOODIX_READ_COOR_ADDR + 1 + GOODIX_CONTACT_SIZE, data, GOODIX_CONTACT_SIZE * (touch_num - 1)); if (error) return error; } return touch_num; } usleep_range(1000, 2000); /* Poll every 1 - 2 ms */ } while (time_before(jiffies, max_timeout)); /* * The Goodix panel will send spurious interrupts after a * 'finger up' event, which will always cause a timeout. */ return 0; } static void goodix_ts_report_touch(struct goodix_ts_data *ts, u8 *coor_data) { int id = coor_data[0] & 0x0F; int input_x = get_unaligned_le16(&coor_data[1]); int input_y = get_unaligned_le16(&coor_data[3]); int input_w = get_unaligned_le16(&coor_data[5]); input_mt_slot(ts->input_dev, id); input_mt_report_slot_state(ts->input_dev, MT_TOOL_FINGER, true); touchscreen_report_pos(ts->input_dev, &ts->prop, input_x, input_y, true); input_report_abs(ts->input_dev, ABS_MT_TOUCH_MAJOR, input_w); input_report_abs(ts->input_dev, ABS_MT_WIDTH_MAJOR, input_w); } /** * goodix_process_events - Process incoming events * * @ts: our goodix_ts_data pointer * * Called when the IRQ is triggered. Read the current device state, and push * the input events to the user space. */ static void goodix_process_events(struct goodix_ts_data *ts) { u8 point_data[1 + GOODIX_CONTACT_SIZE * GOODIX_MAX_CONTACTS]; int touch_num; int i; touch_num = goodix_ts_read_input_report(ts, point_data); if (touch_num < 0) return; /* * Bit 4 of the first byte reports the status of the capacitive * Windows/Home button. */ input_report_key(ts->input_dev, KEY_LEFTMETA, point_data[0] & BIT(4)); for (i = 0; i < touch_num; i++) goodix_ts_report_touch(ts, &point_data[1 + GOODIX_CONTACT_SIZE * i]); input_mt_sync_frame(ts->input_dev); input_sync(ts->input_dev); } /** * goodix_ts_irq_handler - The IRQ handler * * @irq: interrupt number. * @dev_id: private data pointer. */ static irqreturn_t goodix_ts_irq_handler(int irq, void *dev_id) { struct goodix_ts_data *ts = dev_id; goodix_process_events(ts); if (goodix_i2c_write_u8(ts->client, GOODIX_READ_COOR_ADDR, 0) < 0) dev_err(&ts->client->dev, "I2C write end_cmd error\n"); return IRQ_HANDLED; } static void goodix_free_irq(struct goodix_ts_data *ts) { devm_free_irq(&ts->client->dev, ts->client->irq, ts); } static int goodix_request_irq(struct goodix_ts_data *ts) { return devm_request_threaded_irq(&ts->client->dev, ts->client->irq, NULL, goodix_ts_irq_handler, ts->irq_flags, ts->client->name, ts); } static int goodix_check_cfg_8(struct goodix_ts_data *ts, const struct firmware *cfg) { int i, raw_cfg_len = cfg->size - 2; u8 check_sum = 0; for (i = 0; i < raw_cfg_len; i++) check_sum += cfg->data[i]; check_sum = (~check_sum) + 1; if (check_sum != cfg->data[raw_cfg_len]) { dev_err(&ts->client->dev, "The checksum of the config fw is not correct"); return -EINVAL; } if (cfg->data[raw_cfg_len + 1] != 1) { dev_err(&ts->client->dev, "Config fw must have Config_Fresh register set"); return -EINVAL; } return 0; } static int goodix_check_cfg_16(struct goodix_ts_data *ts, const struct firmware *cfg) { int i, raw_cfg_len = cfg->size - 3; u16 check_sum = 0; for (i = 0; i < raw_cfg_len; i += 2) check_sum += get_unaligned_be16(&cfg->data[i]); check_sum = (~check_sum) + 1; if (check_sum != get_unaligned_be16(&cfg->data[raw_cfg_len])) { dev_err(&ts->client->dev, "The checksum of the config fw is not correct"); return -EINVAL; } if (cfg->data[raw_cfg_len + 2] != 1) { dev_err(&ts->client->dev, "Config fw must have Config_Fresh register set"); return -EINVAL; } return 0; } /** * goodix_check_cfg - Checks if config fw is valid * * @ts: goodix_ts_data pointer * @cfg: firmware config data */ static int goodix_check_cfg(struct goodix_ts_data *ts, const struct firmware *cfg) { if (cfg->size > GOODIX_CONFIG_MAX_LENGTH) { dev_err(&ts->client->dev, "The length of the config fw is not correct"); return -EINVAL; } return ts->chip->check_config(ts, cfg); } /** * goodix_send_cfg - Write fw config to device * * @ts: goodix_ts_data pointer * @cfg: config firmware to write to device */ static int goodix_send_cfg(struct goodix_ts_data *ts, const struct firmware *cfg) { int error; error = goodix_check_cfg(ts, cfg); if (error) return error; error = goodix_i2c_write(ts->client, ts->chip->config_addr, cfg->data, cfg->size); if (error) { dev_err(&ts->client->dev, "Failed to write config data: %d", error); return error; } dev_dbg(&ts->client->dev, "Config sent successfully."); /* Let the firmware reconfigure itself, so sleep for 10ms */ usleep_range(10000, 11000); return 0; } static int goodix_int_sync(struct goodix_ts_data *ts) { int error; error = gpiod_direction_output(ts->gpiod_int, 0); if (error) return error; msleep(50); /* T5: 50ms */ error = gpiod_direction_input(ts->gpiod_int); if (error) return error; return 0; } /** * goodix_reset - Reset device during power on * * @ts: goodix_ts_data pointer */ static int goodix_reset(struct goodix_ts_data *ts) { int error; /* begin select I2C slave addr */ error = gpiod_direction_output(ts->gpiod_rst, 0); if (error) return error; msleep(20); /* T2: > 10ms */ /* HIGH: 0x28/0x29, LOW: 0xBA/0xBB */ error = gpiod_direction_output(ts->gpiod_int, ts->client->addr == 0x14); if (error) return error; usleep_range(100, 2000); /* T3: > 100us */ error = gpiod_direction_output(ts->gpiod_rst, 1); if (error) return error; usleep_range(6000, 10000); /* T4: > 5ms */ /* end select I2C slave addr */ error = gpiod_direction_input(ts->gpiod_rst); if (error) return error; error = goodix_int_sync(ts); if (error) return error; return 0; } /** * goodix_get_gpio_config - Get GPIO config from ACPI/DT * * @ts: goodix_ts_data pointer */ static int goodix_get_gpio_config(struct goodix_ts_data *ts) { int error; struct device *dev; struct gpio_desc *gpiod; if (!ts->client) return -EINVAL; dev = &ts->client->dev; ts->avdd28 = devm_regulator_get(dev, "AVDD28"); if (IS_ERR(ts->avdd28)) { error = PTR_ERR(ts->avdd28); if (error != -EPROBE_DEFER) dev_err(dev, "Failed to get AVDD28 regulator: %d\n", error); return error; } ts->vddio = devm_regulator_get(dev, "VDDIO"); if (IS_ERR(ts->vddio)) { error = PTR_ERR(ts->vddio); if (error != -EPROBE_DEFER) dev_err(dev, "Failed to get VDDIO regulator: %d\n", error); return error; } /* Get the interrupt GPIO pin number */ gpiod = devm_gpiod_get_optional(dev, GOODIX_GPIO_INT_NAME, GPIOD_IN); if (IS_ERR(gpiod)) { error = PTR_ERR(gpiod); if (error != -EPROBE_DEFER) dev_dbg(dev, "Failed to get %s GPIO: %d\n", GOODIX_GPIO_INT_NAME, error); return error; } // WARNING: SUPER UGLY HACK!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! dev_dbg(dev, "removing ACTIVE_LOW flag"); *((unsigned long*)(((void*)gpiod) + sizeof(void*))) &= ~BIT(6); ts->gpiod_int = gpiod; /* Get the reset line GPIO pin number */ gpiod = devm_gpiod_get_optional(dev, GOODIX_GPIO_RST_NAME, GPIOD_IN); if (IS_ERR(gpiod)) { error = PTR_ERR(gpiod); if (error != -EPROBE_DEFER) dev_dbg(dev, "Failed to get %s GPIO: %d\n", GOODIX_GPIO_RST_NAME, error); return error; } ts->gpiod_rst = gpiod; return 0; } /** * goodix_read_config - Read the embedded configuration of the panel * * @ts: our goodix_ts_data pointer * * Must be called during probe */ static void goodix_read_config(struct goodix_ts_data *ts) { u8 config[GOODIX_CONFIG_MAX_LENGTH]; int x_max, y_max; int error; error = goodix_i2c_read(ts->client, ts->chip->config_addr, config, ts->chip->config_len); if (error) { dev_warn(&ts->client->dev, "Error reading config: %d\n", error); ts->int_trigger_type = GOODIX_INT_TRIGGER; ts->max_touch_num = GOODIX_MAX_CONTACTS; return; } ts->int_trigger_type = config[TRIGGER_LOC] & 0x03; ts->max_touch_num = config[MAX_CONTACTS_LOC] & 0x0f; x_max = get_unaligned_le16(&config[RESOLUTION_LOC]); y_max = get_unaligned_le16(&config[RESOLUTION_LOC + 2]); if (x_max && y_max) { input_abs_set_max(ts->input_dev, ABS_MT_POSITION_X, x_max - 1); input_abs_set_max(ts->input_dev, ABS_MT_POSITION_Y, y_max - 1); } } /** * goodix_read_version - Read goodix touchscreen version * * @ts: our goodix_ts_data pointer */ static int goodix_read_version(struct goodix_ts_data *ts) { int error; u8 buf[6]; char id_str[5]; error = goodix_i2c_read(ts->client, GOODIX_REG_ID, buf, sizeof(buf)); if (error) { dev_err(&ts->client->dev, "read version failed: %d\n", error); return error; } memcpy(id_str, buf, 4); id_str[4] = 0; if (kstrtou16(id_str, 10, &ts->id)) ts->id = 0x1001; ts->version = get_unaligned_le16(&buf[4]); dev_info(&ts->client->dev, "ID %d, version: %04x\n", ts->id, ts->version); return 0; } /** * goodix_i2c_test - I2C test function to check if the device answers. * * @client: the i2c client */ static int goodix_i2c_test(struct i2c_client *client) { int retry = 0; int error; u8 test; while (retry++ < 2) { error = goodix_i2c_read(client, GOODIX_REG_ID, &test, 1); if (!error) return 0; dev_err(&client->dev, "i2c test failed attempt %d: %d\n", retry, error); msleep(20); } return error; } /** * goodix_configure_dev - Finish device initialization * * @ts: our goodix_ts_data pointer * * Must be called from probe to finish initialization of the device. * Contains the common initialization code for both devices that * declare gpio pins and devices that do not. It is either called * directly from probe or from request_firmware_wait callback. */ static int goodix_configure_dev(struct goodix_ts_data *ts) { int error; ts->int_trigger_type = GOODIX_INT_TRIGGER; ts->max_touch_num = GOODIX_MAX_CONTACTS; ts->input_dev = devm_input_allocate_device(&ts->client->dev); if (!ts->input_dev) { dev_err(&ts->client->dev, "Failed to allocate input device."); return -ENOMEM; } ts->input_dev->name = "Goodix Capacitive TouchScreen"; ts->input_dev->phys = "input/ts"; ts->input_dev->id.bustype = BUS_I2C; ts->input_dev->id.vendor = 0x0416; ts->input_dev->id.product = ts->id; ts->input_dev->id.version = ts->version; /* Capacitive Windows/Home button on some devices */ input_set_capability(ts->input_dev, EV_KEY, KEY_LEFTMETA); input_set_capability(ts->input_dev, EV_ABS, ABS_MT_POSITION_X); input_set_capability(ts->input_dev, EV_ABS, ABS_MT_POSITION_Y); input_set_abs_params(ts->input_dev, ABS_MT_WIDTH_MAJOR, 0, 255, 0, 0); input_set_abs_params(ts->input_dev, ABS_MT_TOUCH_MAJOR, 0, 255, 0, 0); /* Read configuration and apply touchscreen parameters */ goodix_read_config(ts); /* Try overriding touchscreen parameters via device properties */ touchscreen_parse_properties(ts->input_dev, true, &ts->prop); if (!ts->prop.max_x || !ts->prop.max_y || !ts->max_touch_num) { dev_err(&ts->client->dev, "Invalid config (%d, %d, %d), using defaults\n", ts->prop.max_x, ts->prop.max_y, ts->max_touch_num); ts->prop.max_x = GOODIX_MAX_WIDTH - 1; ts->prop.max_y = GOODIX_MAX_HEIGHT - 1; ts->max_touch_num = GOODIX_MAX_CONTACTS; input_abs_set_max(ts->input_dev, ABS_MT_POSITION_X, ts->prop.max_x); input_abs_set_max(ts->input_dev, ABS_MT_POSITION_Y, ts->prop.max_y); } if (dmi_check_system(rotated_screen)) { ts->prop.invert_x = true; ts->prop.invert_y = true; dev_dbg(&ts->client->dev, "Applying '180 degrees rotated screen' quirk\n"); } error = input_mt_init_slots(ts->input_dev, ts->max_touch_num, INPUT_MT_DIRECT | INPUT_MT_DROP_UNUSED); if (error) { dev_err(&ts->client->dev, "Failed to initialize MT slots: %d", error); return error; } error = input_register_device(ts->input_dev); if (error) { dev_err(&ts->client->dev, "Failed to register input device: %d", error); return error; } ts->irq_flags = goodix_irq_flags[ts->int_trigger_type] | IRQF_ONESHOT; error = goodix_request_irq(ts); if (error) { dev_err(&ts->client->dev, "request IRQ failed: %d\n", error); return error; } return 0; } /** * goodix_config_cb - Callback to finish device init * * @ts: our goodix_ts_data pointer * * request_firmware_wait callback that finishes * initialization of the device. */ static void goodix_config_cb(const struct firmware *cfg, void *ctx) { struct goodix_ts_data *ts = ctx; int error; if (cfg) { /* send device configuration to the firmware */ error = goodix_send_cfg(ts, cfg); if (error) goto err_release_cfg; } goodix_configure_dev(ts); err_release_cfg: release_firmware(cfg); complete_all(&ts->firmware_loading_complete); } static void goodix_disable_regulators(void *arg) { struct goodix_ts_data *ts = arg; regulator_disable(ts->vddio); regulator_disable(ts->avdd28); } static int goodix_ts_probe(struct i2c_client *client, const struct i2c_device_id *id) { struct goodix_ts_data *ts; struct dmi_system_id *dmi_match; int error; dev_dbg(&client->dev, "I2C Address: 0x%02x\n", client->addr); if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) { dev_err(&client->dev, "I2C check functionality failed.\n"); return -ENXIO; } ts = devm_kzalloc(&client->dev, sizeof(*ts), GFP_KERNEL); if (!ts) return -ENOMEM; ts->client = client; i2c_set_clientdata(client, ts); init_completion(&ts->firmware_loading_complete); #ifdef CONFIG_ACPI dmi_match = dmi_first_match(need_gpio_mapping); if (dmi_match) { dev_dbg(&client->dev, "GPIO mapping quirk applied.\n"); devm_acpi_dev_add_driver_gpios(&client->dev, dmi_match->driver_data); } #endif error = goodix_get_gpio_config(ts); if (error) return error; /* power up the controller */ error = regulator_enable(ts->avdd28); if (error) { dev_err(&client->dev, "Failed to enable AVDD28 regulator: %d\n", error); return error; } error = regulator_enable(ts->vddio); if (error) { dev_err(&client->dev, "Failed to enable VDDIO regulator: %d\n", error); regulator_disable(ts->avdd28); return error; } error = devm_add_action_or_reset(&client->dev, goodix_disable_regulators, ts); if (error) return error; if (ts->gpiod_int && ts->gpiod_rst) { /* reset the controller */ error = goodix_reset(ts); if (error) { dev_err(&client->dev, "Controller reset failed.\n"); return error; } } error = goodix_i2c_test(client); if (error) { dev_err(&client->dev, "I2C communication failure: %d\n", error); return error; } error = goodix_read_version(ts); if (error) { dev_err(&client->dev, "Read version failed.\n"); return error; } ts->chip = goodix_get_chip_data(ts->id); if (ts->gpiod_int && ts->gpiod_rst) { /* update device config */ ts->cfg_name = devm_kasprintf(&client->dev, GFP_KERNEL, "goodix_%d_cfg.bin", ts->id); if (!ts->cfg_name) return -ENOMEM; error = request_firmware_nowait(THIS_MODULE, true, ts->cfg_name, &client->dev, GFP_KERNEL, ts, goodix_config_cb); if (error) { dev_err(&client->dev, "Failed to invoke firmware loader: %d\n", error); return error; } return 0; } else { error = goodix_configure_dev(ts); if (error) return error; } return 0; } static int goodix_ts_remove(struct i2c_client *client) { struct goodix_ts_data *ts = i2c_get_clientdata(client); if (ts->gpiod_int && ts->gpiod_rst) wait_for_completion(&ts->firmware_loading_complete); return 0; } static int __maybe_unused goodix_suspend(struct device *dev) { struct i2c_client *client = to_i2c_client(dev); struct goodix_ts_data *ts = i2c_get_clientdata(client); int error; /* We need gpio pins to suspend/resume */ if (!ts->gpiod_int || !ts->gpiod_rst) { disable_irq(client->irq); return 0; } wait_for_completion(&ts->firmware_loading_complete); /* Free IRQ as IRQ pin is used as output in the suspend sequence */ goodix_free_irq(ts); /* Output LOW on the INT pin for 5 ms */ error = gpiod_direction_output(ts->gpiod_int, 0); if (error) { goodix_request_irq(ts); return error; } usleep_range(5000, 6000); error = goodix_i2c_write_u8(ts->client, GOODIX_REG_COMMAND, GOODIX_CMD_SCREEN_OFF); if (error) { dev_err(&ts->client->dev, "Screen off command failed\n"); gpiod_direction_input(ts->gpiod_int); goodix_request_irq(ts); return -EAGAIN; } /* * The datasheet specifies that the interval between sending screen-off * command and wake-up should be longer than 58 ms. To avoid waking up * sooner, delay 58ms here. */ msleep(58); return 0; } static int __maybe_unused goodix_resume(struct device *dev) { struct i2c_client *client = to_i2c_client(dev); struct goodix_ts_data *ts = i2c_get_clientdata(client); int error; if (!ts->gpiod_int || !ts->gpiod_rst) { enable_irq(client->irq); return 0; } /* * Exit sleep mode by outputting HIGH level to INT pin * for 2ms~5ms. */ error = gpiod_direction_output(ts->gpiod_int, 1); if (error) return error; usleep_range(2000, 5000); error = goodix_int_sync(ts); if (error) return error; error = goodix_request_irq(ts); if (error) return error; return 0; } static SIMPLE_DEV_PM_OPS(goodix_pm_ops, goodix_suspend, goodix_resume); static const struct i2c_device_id goodix_ts_id[] = { { "GDIX1001:00", 0 }, { } }; MODULE_DEVICE_TABLE(i2c, goodix_ts_id); #ifdef CONFIG_ACPI static const struct acpi_device_id goodix_acpi_match[] = { { "GDIX1001", 0 }, { "GDIX1002", 0 }, { } }; MODULE_DEVICE_TABLE(acpi, goodix_acpi_match); #endif #ifdef CONFIG_OF static const struct of_device_id goodix_of_match[] = { { .compatible = "goodix,gt1151" }, { .compatible = "goodix,gt5663" }, { .compatible = "goodix,gt5688" }, { .compatible = "goodix,gt911" }, { .compatible = "goodix,gt9110" }, { .compatible = "goodix,gt912" }, { .compatible = "goodix,gt927" }, { .compatible = "goodix,gt9271" }, { .compatible = "goodix,gt928" }, { .compatible = "goodix,gt967" }, { } }; MODULE_DEVICE_TABLE(of, goodix_of_match); #endif static struct i2c_driver goodix_ts_driver = { .probe = goodix_ts_probe, .remove = goodix_ts_remove, .id_table = goodix_ts_id, .driver = { .name = "Goodix-TS", .acpi_match_table = ACPI_PTR(goodix_acpi_match), .of_match_table = of_match_ptr(goodix_of_match), .pm = &goodix_pm_ops, }, }; module_i2c_driver(goodix_ts_driver); MODULE_AUTHOR("Benjamin Tissoires "); MODULE_AUTHOR("Bastien Nocera "); MODULE_DESCRIPTION("Goodix touchscreen driver"); MODULE_LICENSE("GPL v2");