Package Details: rtl88x2bu-dkms-git 5.6.1.r30.20fba52-1

Git Clone URL: https://aur.archlinux.org/rtl88x2bu-dkms-git.git (read-only, click to copy)
Package Base: rtl88x2bu-dkms-git
Description: Kernel module for Realtek rtl88x2bu WiFi chipset
Upstream URL: https://github.com/RinCat/RTL88x2BU-Linux-Driver
Licenses: GPL2
Submitter: RinCat
Maintainer: RinCat
Last Packager: RinCat
Votes: 7
Popularity: 0.49
First Submitted: 2018-11-23 23:14
Last Updated: 2019-09-21 10:30

Dependencies (3)

Required by (0)

Sources (1)

Latest Comments

« First ‹ Previous 1 2 3 4 5 6 Next › Last »

RinCat commented on 2019-12-20 05:06

@pokemod97 I can't confirm your device chip, 0bda:c811 is 8811CU ID, but the driver from the website is 88x2BU.

pokemod97 commented on 2019-12-20 04:55

@RinCat I'm trying to use the Cudy WU650S http://www.cudytech.com/spqxz with your driver version on linux 5.4.5. However there is no indication it's working. $ dkms status

rtl88x2bu, 5.6.1.r45.da6be1b, 5.4.5-arch1-1, x86_64: installed $lsusb -v Bus 001 Device 005: ID 0bda:c811 Realtek Semiconductor Corp. 802.11ac NIC Couldn't open device, some information will be missing Is my USB ID not whitelisted or are there other trouble shooting steps I can do?

RinCat commented on 2019-11-30 19:35

@samwwjd710 The USB ID is customizable by the vendors, and if your manufacturer change it to something else it has to be added to the driver whitelist. Which what I did after you post. If you are not using DKMS, it just "make ; sudo make install ; sudo modprobe 88x2bu"

samwwjd710 commented on 2019-11-30 18:36

@RinCat

Thanks for replying!

I had tried the one you updated on September 21st.

Am I doing something wrong? Did I mess up your driver when I compiled and modprobe my own? Is there a command I need to run after installing your AUR package driver that will change it over or something?

I'm trying again today but I don't have a ton of hope. :)

RinCat commented on 2019-11-15 00:10

@samwwjd710 I have updated the driver, try the new git version.

samwwjd710 commented on 2019-11-14 22:25

Maybe you can help? I had been using this https://github.com/EntropicEffect/rtl8822bu.git driver since Kubuntu 18.10 before I switched to using Manjaro. It worked up through 4.19 kernel but now it isn't working on 5.2 or 5.3 any of them. So when manjaro updates my wifi borks! I keep rolling back to kernel 4.19 but I'd like to used your driver and the newer kernel if I can figure out why that isn't working... I have a backup wifi that works plug and play on most linux but it's slow like 240kbps tops. lol

I tried using this instead, and I installed it from the package manager.. but it wont work for me.

I tried going in to the folder '/usr/src/rtl88x2bu-5.6.1.r30.20fba52/' and doing a >make >sudo make install >modprobe 88x2bu ... kinda like I used to do with the older driver..

Maybe you can help me figure out what I'm doing wrong? I'd like to use the latest kernel, with this driver..

Maybe this is the wrong driver for me. or I'm using wrong commands... I have a DWA 182 Revision D1 or Dlink ac1200 rev d1. It has a rtl8812bu chipset.

:) Thanks in advance for any help.

RinCat commented on 2019-09-22 18:57

@lucaskfreitas dmesg should shows the error. But try use "sudo mkinitcpio -P" and reboot first.

lucaskfreitas commented on 2019-09-22 11:18

Hello, updating to version 5.6.1.r30.20fba52-1 did not solve the kernel 5.3 problem for me. There are no error messages, and it apparently has installed successfully, but the wifi dongle isn't recognized. In previous versions, it has worked out-of-the-box. Is there some way for me to check what went wrong?

RinCat commented on 2019-09-21 10:31

Base version updated to 5.6.1, tested on Linux 5.3.

said commented on 2019-09-21 09:03

Done, it works, thanks!